Atlanta Build Expo Booths for Building Products

Atlanta Build Expo Booths for Building Products

Displays for building product and contractor exhibitors at Atlanta Build Expo: heavy sample walls, tool demo tables, mockups and a well-planned install.

Building products are heavy and best understood in place. A roofing shingle means more on a small roof mockup than in a binder. A flooring line reads better as a laid section than as samples on a shelf. For exhibitors at Atlanta Build Expo, the display has to carry heavy samples, show products installed and give contractors and architects room to touch, measure and ask questions.

For a building products maker we often lay out a 10 by 20 inline with a sample wall across the back holding siding, trim and window profiles on heavy brackets, a small corner mockup showing the product installed on a section of wall, a tool demo table at the front where a rep shows the install method, and a counter with spec sheets and sample cards.

Heavy samples on the wall

Building samples weigh more than most trade show product. We plan sample walls on a steel-reinforced frame or heavy slatwall with brackets rated for the load, and keep the heaviest pieces low. Samples are mounted with screws or clips that let a contractor lift the edge and look at the back without pulling the piece off the wall.

  • Siding and trim profiles hang on rails at different heights to show length and finish.
  • Flooring and tile sit on angled shelves or a short laid section on a platform.
  • Window and door profiles stand in a cutaway frame.
  • Sample cards and swatches sit in a rack at the counter.

We set the bracket spacing and the sample order on that wall during trade show booth design.

Mockups and demo tables

A mockup shows the product installed. We build small wall or roof sections on a frame in the booth corner, with the product applied by your team or built ahead of time by a build partner and shipped as a unit. Tool demo tables have a sturdy top, a tool rack and a power drop for cordless chargers or corded tools. If the demo creates dust or debris, we add a mat under the table and plan a shop vacuum in the closet.

Tool demos need power ordered through the show, and we mark each drop at the demo table on the floor plan. Our custom exhibit builds page covers mockup construction.

Crating samples and mockups

Heavy samples and mockups ship best in crates, not cases. We plan crates with internal bracing so siding panels and window profiles stand on edge without rubbing, and we label each crate with its weight and contents so the show's material handling crew can lift it safely. Mockups travel as one or two pieces bolted to a base, with the product already applied, which turns a long on-site build into a placement and a few bolts.

Crates are emptied and stored during the show, then brought back for teardown. Heavy sample crates move between the dock and the booth under our drayage and material handling coordination.

Artwork for builders

Builders and contractors want product names, applications and warranty facts at a glance. The backwall header carries the company name and product category. Each sample section gets a small sign with the product name, sizes and finish options. Fabric graphics on the header and printed signs on the wall work well. Panel art for the sample wall is approved and printed weeks before the hall opens for move-in. The panels are produced by a build partner or your own vendor, and we provide the dimensions and check each piece when it lands. Files for those panels are prepared through our exhibit graphics production service.

Move-in sequence

Carpet goes down first, then the reinforced frame, then the sample wall brackets, each one checked against the weight list before a product hangs on it. The mockup frame goes up in the corner. Your team or the install crew mounts the heavy samples, and the tool demo table and counter go in last. Lights and power are connected and tested. Your lead and the install crew chief go over the finished booth together: bracket loads, mockup stability, demo table power and spec sheets.

The rest of that order of work is described on our installation and dismantle page.

What to send us

We need the booth number and space size, every sample with its weight and dimensions, any drawings of the mockup, the tools in the demo and your logo files. Photos from a past show help us understand how the samples were mounted before.

If a mockup is built ahead of time, tell us who is building it and when it will be ready, so we can schedule its shipping crate and plan the booth corner around its exact footprint.

Teardown

At close the crew takes down the heavy samples first and stacks them on carts, then strips graphics and breaks down the sample wall, mockup and frame. Tools and spec sheets go back into your cases. Each case is checked off the packing list and tagged for the return freight or for storage. We note any damaged bracket or mockup panel for repair before the next show. Samples that were handled all week are set aside so your team can decide whether to replace them with fresh pieces before they go back on the wall.

Questions Exhibitors Ask

How much weight can a sample wall hold?

It depends on the frame and brackets. We plan each wall around your heaviest samples and use steel-reinforced frames or heavy slatwall where needed.

Can you build a roof or wall mockup?

Yes. Mockups are built on a frame in the booth, either on site or ahead of time by a build partner and shipped as a unit. Shipping a finished mockup usually saves the most time on move-in day, because the crew only has to set it in place and bolt it to the frame.

What should we send first?

Send the booth number, the sample list with weights and sizes, any mockup ideas and your artwork or brand guide.

Send the show, venue and booth details

Call (404) 963-0416 or send the show, the hall and your booth number and we will plan the display, the install and the teardown.


Installation and DismantleBooth DesignDisplay TypesServicesVenuesService AreasAboutPlan Your Display(404) 963-0416